Press "Enter" to skip to content

25 Comments

  1. stuartaft stuartaft

    7:00 Perfect time to have a drink of Coca Cola

  2. Simon Wilson Simon Wilson

    Great video – very informative thanks. I broke a mast recently in a laser. Different scale I know but the same issues – big surprise followed by “what do I do now.” Managed to sail downwind with scrap of sail and mast left standing.

  3. 29erUSA128team 29erUSA128team

    What kind of boat is that. Im

  4. jimmiethegerman jimmiethegerman

    You should really cut them some slack here. This was a neat video which demonstrates what happens when a mast breaks. Of course they could have asserted that the mast would fall to leeward. Not a guarantee, but most likely the mast will ALWAYS fall to leeward with the sails up. They did a neat experiment and had to consolidate it down to a 15 min. video so that it is watchable. It had my attention the whole way through. TOO critical. You go make a video like this and then let me at the comments

  5. jimmiethegerman jimmiethegerman

    That wire was already half way hacked through if you look closely. It takes a while and it is frustrating to hack saw though 1×19. The best tool is probably the bullet blast thingy. Quick and effortless. The Hydraulic cutters are great but cost about $2k depending on what size wire you need to cut.

  6. johnnsweeney johnnsweeney

    If you intent is to provide a mast recovery exercise to novices, great.
    But if you are honestly looking to understand how or why a rig fails, perhaps you might apply a bit of science and engineering?
    Contrary to your introduction, it was entirely predictable that the rig would buckle at the lower shroud attachment point when it was in place and the upper shroud parted. It was also predictable that, given no backstay tension and under-trimmed jib, that the mast would fall to leeward. Get serious

  7. richardmg9 richardmg9

    >.<

  8. ianrkav ianrkav

    I guess so:-) Still, it keeps the mast makers in business:-)

  9. richardmg9 richardmg9

    everything breaks

  10. YachtingMonthly YachtingMonthly

    You’ll see how we did this in the next video in the series: Jury Rigs

  11. crkemppainen crkemppainen

    Informative. Now lets see how to stand a mast at sea without a crane

  12. Randy Eakin Randy Eakin

    i thought it was interesting that the cheapest, nearly quickest and multi-use tool for cutting the stays was the hacksaw.

  13. ianrkav ianrkav

    Maybe not:-)

  14. SuperPhunThymes SuperPhunThymes

    If the mast is unbreakable, then the boat itself will break somewhere!

  15. percymain2 percymain2

    no helmets?!

  16. ianrkav ianrkav

    Has anyone designed an unbreakable mast yet?

  17. sailmattdxb sailmattdxb

    by suprise is an under statement…… dismasted a 20 ft e-boat it was more than a suprise……

  18. DROPPERSPRODUCTION DROPPERSPRODUCTION

    I really love sailing, that sailboat and that condition -> I can look at this vid all day long!

  19. elimonjal elimonjal

    difficult to understand this guys accent

  20. jaap blues jaap blues

    oops! looks like my own summer-experience at the northsea……..

  21. Graham Snook Graham Snook

    Because he didn’t want to? :0)

  22. holmatromarine holmatromarine

    Nice movie!
    Please not that cutting nitronic rod is a complete different story, please watch this blog:
    blog.apsltd.com/2009/06/video-blog-holmatro-wirerod-cutters.html

  23. Ocean71 Ocean71

    Top movie. Thanks a lot.

  24. chucklestoo chucklestoo

    The bottom section goes as well due to the loss of the backstay? Higher on the wind, would the top section have come backwards and the babystay have kept the bottom section up? Obviously more dangerous for the test crew though…A fractional rig would probably just go at the spreaders.

  25. Waaranti Waaranti

    why doesnt the skipper wear a lifejacket????????

Comments are closed.